Hooks & Holders
Holders that keep equipment in place on the rail, deck and bulkhead: outboard motor brackets, fishing rod holders with gasket and inner insert for flush-mount rod holders, drink, bottle and table top holders, holders for lifebuoys and lifebuoy lights, flagpole and boat hook holders, fender baskets, Fastfender quick-release fender hooks, spiral hooks for sail ties, eye bolts, hatch fasteners, rowlock sockets and door stops.
| Description | Item no. | Dimension | Material | Unit | Price | Delivery time | ||
|---|---|---|---|---|---|---|---|---|
| Rubber inner liner for flush-mount rod holder with cap | RH-IGD | single | 5,29 EUR per piece | 3 to 5 working days | ||||
| Horseshoe lifebuoy and light holder, 370 mm, stainless steel A2 | RRH-37 | A2 / V2A | single | 19,99 EUR per piece | 3 to 5 working days | |||
| Lifebuoy and light holder, 65 cm, stainless steel A2 | RRH-65 | A2 / V2A | single | 29,99 EUR per piece | 3 to 5 working days | |||
![]() | Rod holder 230 mm for rail mounting3 versions | from 26,99 EUR per piece | 5 to 8 working days | All versions | ||||
| Für Rohr-Ø 19 bis 25 mm, Edelstahl A2 | RH-R2-230-19 | For tube Ø 19 bis 25 mm | A2 / V2A | single | 27,99 EUR per piece | 5 to 8 working days | ||
| Für Rohr-Ø 19 bis 25 mm, Edelstahl A4 | RH-R4-230-19 | For tube Ø 19 bis 25 mm | A4 / V4A | single | 45,99 EUR per piece | 5 to 8 working days | ||
| Für Rohr-Ø 22 bis 25 mm, Edelstahl A2 | RH-R2-230 | For tube Ø 22 bis 25 mm | A2 / V2A | single | 26,99 EUR per piece | 5 to 8 working days | ||
![]() | Sturdy fender basket for 2 fenders, port side, stainless steel A42 versions | from 115,99 EUR per piece | 5 to 8 working days | All versions | ||||
| Ø 175 mm | FK-28L-18 | Diameter 175 mm | A4 / V4A | single | 115,99 EUR per piece | 5 to 8 working days | ||
| Ø 225 mm | FK-28L-22 | Diameter 225 mm | A4 / V4A | single | 138,99 EUR per piece | 5 to 8 working days | ||
| Sturdy fender basket for 2 fenders, starboard, Ø 175 mm, stainless steel A4 | FK-28R-18 | Diameter 175 mm | A4 / V4A | single | 115,99 EUR per piece | 3 to 5 working days | ||
Choosing the right hooks and holders on board
Measure the rail tube first
Many holders sit directly on the rail. Flagpole holders, drink holders and rod holders for rail mounting are made for specific tube diameters, which are given for each version. Measure the outer diameter of your rail tube before you order. For the flagpole holder, also choose the diameter of your flagpole; this too is given for each version. Other holders are mounted on the wall or on the deck, such as the bottle holder for wall mounting or the triple drink holder with welded-in screws for deck mounting.
Adjusting fenders quickly
The Fastfender hangs on the guardrail wire or the rail tube and holds the fender line in a built-in clamp. Fastfender describes the handling as follows: thread the line through the holder from below, pull it slightly to adjust until it comes out of the clamp, bring the fender to the right height and insert the line again. Secure the end of the line with a simple knot or a figure-of-eight knot. Choose the version to suit the rail diameter and the line thickness. The A4 fender baskets each hold two fenders; there are separate versions for port and for starboard.
Mind the load and the material
Outboard motor brackets have a maximum load, which is given for each version; compare it with the weight of your engine. The load capacity is also given for the folding table top holder. The lockable fishing rod holder is secured with a padlock. You will find stainless steel padlocks under Equipment; check before buying whether the lock fits the holder.
The outboard motor, lifebuoy, bottle and table top holders are made of A2. A2 is resistant indoors, in the weather and in fresh water; in salt water surface rust may appear, so rinse these holders with fresh water after trips in salt water. The guide V2A, V4A or duplex on the boat explains which stainless steel belongs where.


