Stainless steel pins
Grub screws, cylindrical pins, spring pins and grooved pins made of stainless steel for clamping, fixing and positioning. Each series covers the dimensions of one standard; article number, material and packaging unit are shown for every version.






Standards, materials and dimensions at a glance
| Standard | Item | Material | Dimensions | Versions |
|---|---|---|---|---|
| DIN 7 | Cylindrical pins form A, tolerance zone m6, DIN 7, stainless steel A4 and 1.4305 | A1, A4 / V4A | Ø 2,5 to 12 mm | 4 |
| DIN 1474 | Insert grooved pins, DIN 1474, 6 x 16 mm, stainless steel 1.4305 | A1 | Ø 6 mm | 1 |
| ISO 4027 | Hexagon socket set screws with cone point, ISO 4027, stainless steel A4 | A4 / V4A | Ø 4 to 10 mm | 2 |
| ISO 4028 | Hexagon socket set screws with dog point, ISO 4028, stainless steel A2 | A2 / V2A | Ø 12 mm | 2 |
| ISO 8752 | Spring pins, slotted, heavy duty, ISO 8752, stainless steel 1.4310 | 1.4310 | Ø 3 to 10 mm | 5 |
| no DIN/ISO | Grub screws M6 x20 mm, flat point, stainless steel A4 | A4 / V4A | M6 | 1 |
Which pin for which purpose
Pins connect, secure and position components. Grub screws clamp by pressure, for example a hub or a collar on a shaft. Cylindrical pins, spring pins and grooved pins sit with an interference fit in a bore and hold two components in position relative to each other. The overview above this text shows which standards, materials and dimensions are in the range.
Grub screws: the point style decides
| Point style | Standard (formerly) | Effect and use |
|---|---|---|
| Truncated cone (flat point) | ISO 4026 (DIN 913) | presses flat onto the mating surface and hardly marks the shaft; for adjustable stops and positions that are repositioned |
| Cone point | ISO 4027 (DIN 914) | sits in a pre-drilled conical countersink in the shaft and clamps well; hardly any readjustment afterwards |
| Dog point | ISO 4028 (DIN 915) | engages in a matching bore or groove and does not deform the shaft; each position needs its own counter bore |
| Cup point | ISO 4029 (DIN 916) | cuts into the shaft without pre-drilling; for permanent connections where marking of the shaft is acceptable |
Grub screws are designed for compressive loads only and are not suitable for tensile loads. ISO 4028 provides short and long dog points; which one applies depends on the pin length. The mechanical properties of grub screws made of stainless steel are governed by ISO 3506 Part 3 through hardness classes; grub screws in A2 and A4 are supplied, for example, in hardness class 21H, which corresponds to 210 HV.
Cylindrical pins DIN 7 and ISO 2338
Cylindrical pins are solid pins. They are pressed into a bore that is slightly smaller than the pin and are held by the deformation of the surrounding material. Form A comes with tolerance field m6; for this the bore must be very precise and straight and is usually drilled and then reamed. If the connection has to be released frequently, a taper pin is recommended. DIN 7 has been withdrawn and replaced by ISO 2338. ISO measures the length including the crowned ends, DIN excludes them; some nominal lengths therefore differ.
Spring pins ISO 8752, heavy duty version
Slotted spring pins are thicker than their nominal size before installation, up to 6.7 mm for a nominal size of 6 mm. When pressed in, the pin is compressed via the slot, and the spring action of the material holds it in the bore by friction. Spring pins bridge larger bore tolerances than solid pins and are also suitable for cast or punched bores. The heavy duty version has a considerably greater wall thickness than the light duty version ISO 13337, 1.25 mm compared with 0.75 mm for a nominal size of 6 mm. ISO 8752 replaces DIN 1481.
The material 1.4310 is a classic material for corrosion-resistant springs. Its corrosion resistance is lower than that of 1.4301 (A2).
Half-length grooved pins DIN 1474 and ISO 8741
Half-length grooved pins have three pressed-in longitudinal grooves over half their length. The ridges next to the grooves are larger than the nominal size and form the clamping fit in the bore, for example 4.15 to 4.30 mm for a nominal size of 4 mm, depending on the length. Grooved pins allow larger bore tolerances than cylindrical pins. They are used for positioning and guiding parts and for rotating connections, and are easy to install. DIN 1474 has been withdrawn; its successor standard ISO 8741 is available in the 2025 edition.
Choosing the material
A2 (1.4301) is a widely used stainless steel for fasteners. A4 (1.4401) is alloyed with molybdenum and is considerably more corrosion-resistant. 1.4305 belongs to steel grade A1: the added sulphur makes it easy to machine and lowers its corrosion resistance. A1 is not suitable for environments containing chlorides, such as seawater or swimming pools. A4 too reaches its limits in many marine environments and in swimming pools with chloride-containing cleaning.
